manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 30 / 276

Share
Download
Keysight N9923A User Manual Download Page 30

 30                                                                                                                     Keysight N9923-90001 User’s Guide

Preparing for Initial Use of Your New FieldFox
Take the FieldFox Tour

Top Panel

Side Panel

Caption

Descriptions

Learn More:

Port 1

 

For CAT and NA measurements, use to make reflection measurements. 

Maximum: ±50 VDC, +23 dBm RF

“CAT Mode Settings” 

on page 77

 

 

“NA Mode Settings” on 

page 39

Ext Trig/

 

Ext Ref

External reference BNC connector for use with and External Frequency 

Reference. 
Maximum: 5.5 VDC.
External Triggering is not used on the N9923A.

“Frequency Reference 

Source” on page 226

.

 

 

Port 2

 

For CAT and NA mode. Contains source and B/R2 receivers.
Maximum: ±50 VDC, +23 dBm RF.

“CAT Mode Settings” 

on page 77

 

 

“NA Mode Settings” on 

page 39

Connector

Description

Learn More:

Ethernet cable connector to read trace data using the FieldFox Data Link 

Software and connect to the FieldFox remotely.
Download the latest version of the software at: 

www.keysight.com/find/fieldfoxsupport 

“LAN Settings” on 

page 229

Reserved for future use.

 --

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments