Keysight N9923A User Manual Download Page 173

Page: 173 / 276

173

Keysight N9923A Handheld Analyzer
User’s Guide

12 Data Analysis Features

The following features can be used to analyze the NA and CAT mode
measurement results.

In this Chapter

“How to create Markers” on page 174

“How to move a Marker after it is created” on page 174

“About Delta Markers” on page 175

“Marker Table” on page 176

“Coupled Markers” on page 176

“Marker Trace” on page 177

“Marker Format” on page 178

“What Is a ‘Peak’” on page 182

“Marker Functions” on page 183

“How to Create Fixed Limit Lines” on page 185

“Relative Limit Lines” on page 186

“Build From Trace” on page 187

“Limit Options” on page 187

“How to Save and Recall Limits” on page 188

“How to display data and memory traces” on page 189

“How to perform Trace Math ” on page 189

“About Math Operations” on page 190

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 173 / 276

Search results

Summary of Contents for N9923A

Reviews: