Keysight N9923A User Manual Download Page 254

Page: 254 / 276

254 Keysight N9923-90001 User’s Guide

Safety Considerations
To learn how to safely handle and dispose of the FieldFox battery, refer to the Material

Safety Data Sheet for the manufacturer of the battery at:

Overtemperature Discharging:

The system microcontroller prevents the

battery from being discharged if the cell temperature exceeds 65C. Once the

overtemperature discharging protection is tripped, the battery is automatically
shut off which results in turning off the instrument as well.

Passive Protection

Reverse Charging:

A reverse protection diode prevents against damage or lost

data due to a reverse charge polarity applied to the battery terminals.

Primary Overtemperature:

A PTC (positive temperature coefficient) polyfuse in

series between the Li-ion cells and the charging and discharging transistors

will open up and limit current flow to the battery terminals as a function of very

high temperatures. This protection is resettable once the overstress condition

is removed.
The maximum operating temperature of this fuse is 85C.

Secondary Overtemperature:

A second PTC polyfuse built into each Li-ion cell

will open up and limit current flow as a function of very high temperatures.

Tertiary Overtemperature:

A current interrupt device (CID) within each Li-ion

cell will permanently open up when the temperature reaches 95C. As each cell

fuse is permanently interrupted, overall battery performance will become

severely degraded, up to and including disabling the battery.

Overcurrent Fuse:

This is a one-time blow fuse with a rated current of 12A.

To learn how to safely handle and dispose of the FieldFox battery, refer to the
Material Safety Data Sheet for the manufacturer of the battery at:

http://na.support.keysight.com/fieldfox/help/SupHelp/Reference/MSDS.ht
m

Environmental Requirements

Refer to the FieldFox Specifications in

“Specifications/Data Sheet” on

page 265

Electrical Requirements

The FieldFox allows you to use either the lithium-ion battery or the AC/DC
adapter - both are included.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 254 / 276

Search results

Summary of Contents for N9923A

Reviews: