manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 176 / 276

Share
Download
Keysight N9923A User Manual Download Page 176

 176                                                                                                                     Keysight N9923-90001 User’s Guide

Data Analysis Features
All about Markers

How to Create a Delta Marker

— Create a 

Normal

 marker and move it to the reference position. 

— Press 

Delta

. The marker becomes the reference marker and fixed in its 

X-Axis position. 

— Move the delta marker using the numeric keypad, the 

 arrows, or the 

rotary knob. 

— Press 

Enter

 when finished. 

How to move the Reference marker

— Press 

Delta

 to turn the Delta marker OFF. 

— Move the marker to the new position.

— Then press 

Delta

 again, to turn the Delta marker back ON.

Marker Table

The Marker Table can be displayed at the bottom of the FieldFox screen. It can 

display information for up to 6 markers in a full-width window, and up to 3 
markers for a half-width window (NA mode). The marker table “squeezes” the 
graticule area when activated.

How to display the Marker table 

— Press 

Marker

.

— Then 

More

— Then 

Marker Table On Off

.

Coupled Markers

Coupled Markers, available in NA mode only, allows you to simultaneously 
create and move markers that have the same number for all traces. For 
example, when marker 2 is created on a trace, a marker 2 is created for ALL 

traces. When any marker 2 is moved, they all move together to the same 
X-axis position.

— Coupled markers are allowed only in NA mode and are relevant only in 

multi-trace configurations.

— You can have markers that are coupled and others that are uncoupled.

— Peak functions move the marker to the peak on the 

active trace

, while all 

other markers move to the same X-axis position.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments