manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 266 / 276

Share
Download
Keysight N9923A User Manual Download Page 266

 266                                                                                                                     Keysight N9923-90001 User’s Guide

Instrument Calibration
What Are My Choices of Instrument Calibration?

What Are My Choices of Instrument Calibration?

The following types of instrument calibration are available from Keysight 

Technologies service center:

Keysight Calibration 

Includes the test data from the calibration and the 

certificate of calibration, stating the instrument has been 
calibrated and is operating within the published 
specifications.

ANSI Z540 

Calibration

Includes the test data from the calibration and the 

certificate of calibration, stating the instrument has been 
calibrated using a process in compliance with ANSI 
Z540.1 and is operating within the published 

specifications

ISO 17025 

Calibration

Includes the test data from the calibration and the certificate of 

calibration, stating the instrument has been calibrated using a process in 

compliance with ISO 17025 and is operating within the published 
specifications.

Chapter 5, “CAT (Cable and Antenna Test) 

Mode”, on page  75

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments