Keysight N9923A User Manual Download Page 236

Page: 236 / 276

236 Keysight N9923-90001 User’s Guide

System Settings
Service Diagnostics

All data is deleted from the FieldFox internal “

UserData

” partition. This

includes all State files and Trace + State files (*.sta), all Data files (*.csv, *.snp),

all Picture files (*.png), all Cal Kit files, and all Cable files.

External media that is inserted (mini-SD card or USB flash drive) is NOT

erased.

The “

Lost Clusters

“ folder and files are NOT erased because they are part of

the file system housekeeping.

How to Erase User Data

— Press System 7.

— Then Service Diagnostics.

— Then Advanced

— Then Erase User Data

— Then Confirm Erase

— Then the following occurs:

— All data files and folders are deleted from the “UserData” partition.

— A large file of 0s is written to all of the free blocks on the partition.

— The large file is deleted. All blocks released by deleting this file are

now available for use.

— The FieldFox is rebooted, which manages the newly-freed data and

re-writes the factory cal kits and cable files.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 236 / 276

Search results

Summary of Contents for N9923A

Reviews: