manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 179 / 276

Share
Download
Keysight N9923A User Manual Download Page 179

Keysight N9923-90001 User’s Guide

                                                                                                                      179

Data Analysis Features
All about Markers

There are more trace formats available than marker formats. To display marker 
readouts in more formats than are shown here, change the trace format, then 

select 

Default

. Learn how to change format in 

“Format” on page 46

.

Searching with Markers

Marker Searches are used to move markers to locations on the trace which 
exhibits the characteristics of the search criteria. Learn ‘What is a Peak” in 

“What Is a ‘Peak’” on page 182

.

How to Search with Markers

The following menu structure applies to NA Mode. Keystrokes will be slightly 
different for CAT, Pulse Measurements, and SA Modes.

— Activate the marker to be used for the search (NOT necessary with 

Bandwidth search.)

— Then press 

Mrk ->/Tools

.

— Then 

Marker Search 

— Then choose one of the following: 

—

Tracking ON OFF

 (NA Mode ONLY)

——

ON

 causes the active marker to search for the specified criteria 

with each new sweep. Search criteria can include: Target, 

Bandwidth, Peak, Min. The searches begin with the first sweep 
after Tracking is turned ON, based on the current search type. 

Trk

 appears next to the marker number.

——

OFF

 causes a new marker search only when the search feature 

is re-executed.

—

Peak

 Moves the active marker to the HIGHEST amplitude data point of 

the trace. Peak Excursion value is ignored. In SA Mode, the LO 
feed-through signal (0 Hz) is also ignored.

—

Min

 (Not available in DTF) Moves the active marker to the LOWEST 

amplitude data point of the trace.

—

Target

 (NA Mode ONLY) Enter the Target value. The marker moves to 

the first occurrence of the Target value to the right of its current 

position. The FieldFox interpolates between measured data points to 
find the exact Target value to two decimal points. The interpolated 
X-axis value is displayed in the marker readout or marker table. 

Subsequent presses of the Target softkey cause the marker to move 
to the right to find the next occurrence of the Target value. When the 
marker reaches the end of the stimulus range, it “wraps around” and 

continues the search from the beginning of the stimulus range. 

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments