Keysight N9923A User Manual Download Page 41

Page: 41 / 276

Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

All FieldFox settings and features are supported (except Parameter Conversion)
with mixed-mode S-parameters.

How to make mixed-mode S-parameter measurements

— Press

Measure 1

— Then

More

— Then choose from the following:

—

Scc11

Common reflect/common incident for logical port 1.

—

Sdd11

Differential reflect/differential incident for logical port 1.

—

Sdc11

Differential reflect/common incident for logical port 1.

—

Scd11

Common reflect/differential incident for logical port 1.

To make balanced reflection measurements at the DUT output, connect the
DUT output to the FieldFox ports.

Parameter Conversion

In NA Mode ONLY, converts the active S-parameter trace to an equivalent
impedance (Z), admittance (Y), or reciprocal 1/S-parameter

How to select parameter conversions

— Press

Measure 1

— Then select an S-parameter

— Then

More

— Then

Conversion

— Then choose from the following:

—

Off

(default) No conversion is performed.

—

Z Conv (--) or Y Conv (--)

Perform conversion for impedance (Z) or

admittance (Y). Then choose from the following for either:

——

Auto

The displayed S-parameter is converted to the

appropriate Z or Y parameter: Refl for S11 and S22; Trans for
S21 and S12. When the S-parameter is changed, the
appropriate conversion changes automatically.

——

Refl

The displayed S-parameter is converted to Z or Y

reflection, regardless of whether the S-parameter is reflection

(S11 or S22) or transmission (S21 or S12).

Learn more about Balanced Measurements with the FieldFox in the

FieldFox Supplemental Online Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 41 / 276

Search results

Summary of Contents for N9923A

Reviews: