Keysight N9923A User Manual Download Page 151

Page: 151 / 276

Keysight N9923-90001 User’s Guide 151

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

Averaging is performed in the USB Power Sensor before the data is sent to the
FieldFox.

Annotation in the left pane shows the state of the Average setting. When
Manual is selected, the ‘Num of Averages’ is setting is also shown.

How to set Averaging

— Press

BW 2

— Then

Averaging

— Then choose from the following:

—

Auto

Averaging is set to a reasonable value by the USB Power

Sensor.

—

Man

Averaging is set to the value specified in the ‘Num Averages’

setting.

—

Off

Averaging is OFF

—

Num Averages

Select a value using the numeric keypad, then press

Enter

Video Bandwidth

The Video Bandwidth setting enables an FIR (finite impulse response) filter
within the USB Power Sensor. The filter setting affects the appearance of the
trace results.

Video Bandwidth is allowed for all pulse measurements

How to set Video Bandwidth

— Press

BW 2

— Then

Video Band wid th

— Then choose from the following:

—

Off

Video Bandwidth is disabled.

—

Low

Similar to a low pass filter, ripple in the pass band is minimized

but allows higher side-lobes on the filter skirt.

—

Medium

Smooth pass band with reasonable transition ripple.

—

High

The pass band ripple is similar to the OFF setting, but the

transition skirts are smoother.

Single or Continuous Measure

This setting determines whether the FieldFox continuously queries the USB
Power Sensor for data, or only once each time the

Single

button is pressed.

Use

Single

to conserve battery power or to allow you to save or analyze

specific data.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 151 / 276

Search results

Summary of Contents for N9923A

Reviews: