Keysight N9923A User Manual Download Page 180

Page: 180 / 276

180 Keysight N9923-90001 User’s Guide

Data Analysis Features
All about Markers

—

Band wid th ON OFF

(NA Mode ONLY) Use to quickly toggle BW

Markers ON and OFF. When OFF, the marker table appears showing

the X and Y-axis positions of all enabled markers.

—

Band wid th

(NA Mode ONLY) Specify the level in dB from the peak or

valley where bandwidth is measured.

——

Negative

numbers search for a

Peak

bandpass, such as a filter

S21 response.

——Either of the following TWO methods can be used to search for

Valley

or Notch filter, such as the S11 response of a

bandpass filter.

——

Negative

values search down from the TOP (MAX) of the

response.

——

Positive

values search up from the BOTTOM (MIN) of the

notch.

——If you first enter Negative, then Positive values, it may be

necessary to press

Marker

, then

More

, then

Markers All Off

Figure 12-4 S21 of a filter with BW Markers and associated readout values.

The search criteria is -3 dB.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 180 / 276

Search results

Summary of Contents for N9923A

Reviews: