Keysight N9923A User Manual Download Page 96

Page: 96 / 276

96 Keysight N9923-90001 User’s Guide

DTF (Distance to Fault) Measurements
DTF Measurement Settings

——

Delete LIne

Remove the selected Freq/Loss pair from the

table.

—

Clear All

then

Yes

. Remove all Freq/Loss pairs from the table and

resets header information

— Press

Done

to close the Cable Editor.

How to Save or Recall a Cable

— Press

Save Cable

to saves your changes to the specified Storage Device.

Enter a filename using the FieldFox labeler (learn more in

“How to use the

FieldFox labeler ” on page 193

). Learn more about Cable files below.

— Press

Recall Cable

to load a Cable file from the specified Storage Device

—

Storage Device

Changes the device used to save or recall Cable files. This

is a different setting from the Save/Recall Storage Device setting. Choose

from Internal (default setting),

USB

(must be connected) or

SD card.

About Cable files

— Cable files are saved to, and recalled from, the

Cables

folder. If the folder

does not already exist on a USB or SD card, it is created automatically

before storing the file.

— Cable files are stored as *.xml files. Existing cable files that are preloaded

into the FieldFox firmware can be overwritten. Your edited file will NOT be
overwritten when firmware is updated.

— To

DELETE

a Cable file, use the Manage Files feature. Learn more in

“Manage Files” on page 199

How the Freq/Loss pairs are applied

When the cable file contains one Freq/Loss pair, that correction value is
applied to the entire displayed frequency span.

When the cable file contains two or more Freq/Loss pairs, the Loss value that is
used is interpolated from the Freq/Loss pairs and the DTF center frequency.

For example, using a cable file with the following Freq/Loss pairs:

1 GHz: 0.1 dB/m

2 GHz: 0.2 dB/m

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 96 / 276

Search results

Summary of Contents for N9923A

Reviews: