manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 68 / 276

Share
Download
Keysight N9923A User Manual Download Page 68

 68                                                                                                                     Keysight N9923-90001 User’s Guide

Time Domain – Option 010
Time Domain (Transform) Settings

How to select Window settings

— Press 

Meas Setup 4

.

— Then 

Settings

.

— Then press 

 arrows to move to the Window row.

— Then press 

Edit

.

— Then press 

Window

 and choose from the following:

—

Maximum

 

(Maximum – Optimized for dynamic range)

 the noise floor 

is lowered to provide the ability to measure low-level responses. 
(Default setting)

—

Medium

 – Compromise between Min and Max window settings. 

—

Minimum

 – Best Response Resolution, providing the ability to resolve 

between two closely-spaced responses.

— Then press 

Done Edit

.

— Again press 

Done

.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments