Keysight N9923A User Manual Download Page 211

Page: 211 / 276

Keysight N9923-90001 User’s Guide

211

System Settings
Display Settings

Display Settings

You can adjust the FieldFox for optimum viewing in a wide range of lighting

conditions.

Display settings remain through a FieldFox Preset. To cause the display

brightness, color settings, and trace width to remain through a FieldFox shut
down, save the display settings as Preferences. Learn how in

“Save and Reset

Preferences” on page 214

Display Brightness

Change the brightness of the background.

How to set Display Brightness

— Press

System 7

— Then

Display

— Then

Brightness

— Use the

arrows, the rotary knob, or numeric keypad to enter a

value between 0 and 100%.

Display Colors

Change Display Colors to alter the viewing scheme.

How to set Display Colors

— Press

System 7

— Then

Display

— Then

Display Colors

— Then choose one of the following:

Clean the transflective screen with gentle and minimal wiping using

Isopropyl alcohol applied to a lint-free cloth.

Indoor

Outdoor Dusk

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 211 / 276

Search results

Summary of Contents for N9923A

Reviews: