Keysight N9923A User Manual Download Page 205

Page: 205 / 276

Keysight N9923-90001 User’s Guide

205

File Management
Printing

Printing

The current screen or selected files can be printed using a PCL-compatible

printer (like older HP Deskjet printer) connected to one of the FieldFox USB
ports. Newer PCL3GUI photo and all-in-one printers are NOT supported.

Measurements can also be printed using the FieldFox Data Link software.

How to print the current screen or a saved file

To save ink, first select an outdoor (white background) display color. Learn how
in

“How to set Display Colors” on page 211

— Connect the printer to a FieldFox USB port.

The print softkey will appear

ONLY when a compatible printer is connected

— Then press

Save/Recall 9

— Then

Print

and choose from the following:

—

Printer & Page Setup

- Confirm that the printer is connected and

configured properly. The Status line should read “Ready’.

— Make other print settings as desired.

—

Select Files for Printing

- Print up to 16 *.PNG images on one page

that are stored on the Internal drive. Images can NOT be printed from
the USB and SD card.

—Edit the Quick Settings table to select up to FOUR Rows and FOUR

Columns for up to 16 total images to be printed on a single page.

—If necessary, edit the filenames to be printed.

—Select

Done

. Then

Print Selected Files

to begin printing.

——

Print Current Screen

– Immediately prints the FieldFox screen

using the selected Printer and Page Setup settings.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 205 / 276

Search results

Summary of Contents for N9923A

Reviews: