Keysight N9923A User Manual Download Page 66

Page: 66 / 276

66 Keysight N9923-90001 User’s Guide

Time Domain – Option 010
Time Domain (Transform) Settings

— Then choose from:

—

Start

Sets the transform start time.

—

Stop

Sets the transform stop time.

Distance Units

When markers are present on a Time Domain trace, marker X-axis values are

shown both in units of time (seconds) and distance. Select the units in which
the marker distance data is presented.

Distance Units are also used when setting Time Domain Line Loss. Learn more
in.

“Distance Units” on page 66

Choose from: m (meters), or Feet.

Window Layout

This setting is used to create additional traces, or select a new layout for traces
that are already created,

Choose from: x1, x2, x2H, x3H, x3, x4H.

Learn more about multi-trace configurations in

“Multi-Trace Configurations”

on page 43

Transform Window

There are abrupt transitions in a frequency domain measurement at the start

and stop frequencies, causing overshoot and ringing in a Time Domain
response. The Window setting reduces the abruptness of the frequency domain
transitions. This causes you to make a trade off in the Time Domain response.

Zero (0) seconds is always the calibration reference plane. Negative values

are useful if moving the reference plane.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 66 / 276

Search results

Summary of Contents for N9923A

Reviews: