Keysight N9923A User Manual Download Page 43

Page: 43 / 276

Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

Multi-Trace Configurations

In NA Mode you can display multiple traces on the FieldFox screen.

The graphic above shows a x3H configuration. Tr2 is the ACTIVE trace as
indicated by the highlighted

Tr2

Trace Setting Notes

— The Frequency Range, IF BW, Resolution, Average, and Output Power

settings are common for all displayed traces.

— All other trace settings, such as measurement, format, and limit lines, are

applied individually to the ACTIVE trace in the same manner as when a
single trace is present.

— By default, a marker is created on ALL traces. However, they can be created

individually by disabling Coupled Markers. Learn more in

“Coupled

Markers” on page 176

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 43 / 276

Search results

Summary of Contents for N9923A

Reviews: