manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 57 / 276

Share
Download
Keysight N9923A User Manual Download Page 57

Keysight N9923-90001 User’s Guide

                                                                                                                      57

NA (Network Analyzer) Mode
NA Mode Settings

— Then 

Big Readout

—

A

 or 

B

 - The A or B display state is recalled. If none have been defined, 

then the default display state is recalled.

—

OFF

 - The B display state is visible but without the Big Marker 

Readout.

— With A or B selected, then press 

Edit Big Marker (A or B)

— Then edit the following display state settings:

—

Num Traces

 – Choose the Multi-Trace configuration x1, x2, or x3. Only 

overlayed configurations are allowed. Learn more in 

“Multi-Trace 

Configurations” on page 43

.

—

Font Size

 – Choose either Big or Super Big. Super Big marker readout #3 

will cover some of the measurement grid.

—

Trace Settings

 - For each possible trace (1, 2, and 3) select from the 

following:

—

Measurement

 – S-Parameter or Receiver measurement to display. 

S11

 is default. Learn more in 

“About S-parameters” on page 39

.

—

Meas Format

 – 

Log

 is default. Learn more in 

“Format” on page 46

.

—

Band wid th (ON)

 – Marker readout for marker bandwidth search. OFF 

is default. Learn how to set BW parameters in 

“Searching with 

Markers” on page 179

.

—

Big Readout

 - For each marker readout (1, 2, and 3), select from the 

following:

—

Marker #

 - Enter a number from 1 to 6 to create the marker. 1 is 

created by default.

—

Trace #

 - The marker# is created on this trace. Tr1 is selected by 

default. The corresponding Num Traces must first be selected. For 
example, to create a marker on Trace 3, first select Num Traces = x3.

—

Format

 – Format for the marker readout. Select Default to make the 

marker readout format the same as the display format. Default is 
selected by default.

—

Mkr Tracking

 – ON: Select the parameter to track on the standard 

Marker Search menu. OFF is selected by default. When set to ON, 

Peak tracking is set by default. Learn about Marker Tracking in 

“Marker Functions” on page 183

.

—

State

 – Choose from Normal, Delta, or OFF. The default marker (1) is 

created in Normal. Learn more in 

“Marker Functions” on page 183

.

—

Enabled

 – Turns the Big Readout of the corresponding marker ON and 

OFF. The default marker (1) is set ON by default.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments