Keysight N9923A User Manual Download Page 46

Page: 46 / 276

46 Keysight N9923-90001 User’s Guide

NA (Network Analyzer) Mode
NA Mode Settings

—

Full (Default setting)

Only the Settings table is shown on the screen.

The trace window is temporarily not shown.

—

Left

The Settings table is shown to the left of the trace window.

—

Bottom

The Settings table is shown below the trace window.

When finished changing ALL settings, press

Done

to save your settings.

Calibration Settings

NA Mode has a page specifically for making settings that pertain to Port

Extensions, including Velocity Factor and Media Type.

Learn more in

“Port Extensions” on page 54

Learn more about Media Type in

“Waveguide Calibrations” on page 117

How to view and change Calibration Settings

— Press

Meas Setup 4

— Then

Calibration Settings

— Make these settings in the same manner as Quick Settings in the previous

section.

Format

Select the display format in which to present measurement results. This setting

can be changed at any time without affecting calibration accuracy.

The marker on-screen readout can be changed to formats other than the
display format. Learn more in

“Marker Format” on page 178

How to select a NA Format

— Press

Measure 1

— Then

Format [current setting]

— Then choose from the following:

—

Log Magnitude

Displays magnitude in dB

—

Linear

Displays positive values only. Y-axis: Unitless (U) for ratioed

measurements; Watts (W) for unratioed measurements.

—

VSWR

Used mainly for S11 and S22. Displays unitless reflection data.

—

Phase

Displays phase in degrees. The trace ‘wraps’ every 360 degrees,

from +180 to –180, for easy scaling.

Learn more about Display Formats in the FieldFox Supplemental Online

Help:

http://na.support.keysight.com/fieldfox/help/SupHelp/FieldFox.htm

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 46 / 276

Search results

Summary of Contents for N9923A

Reviews: