manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 158 / 276

Share
Download
Keysight N9923A User Manual Download Page 158

 158                                                                                                                     Keysight N9923-90001 User’s Guide

Pulse Measurements Mode – Option 330
Pulse Measurement Settings

Pulse Top

Pulse Top is NOT the same as the pulse Peak. Pulse Top is used to set and 
report the reference power level. You enter a value in percent, and the Pulse 
Top value is reported in the Auto Analysis table in dB down from 100% of the 

reference power level.

How to set Pulse Top

— Press 

Mrk ->/Tools

— Then 

Pulse Top 

— Then enter a percent value between 0 and 100 using the numeric keypad, 

the 

 arrows, or the rotary knob. 

— When set to 10%, 10 dB down from the 100% reference level is 

reported.

— When set to 50%, 3 dB down from the 100% reference level is 

reported.

— When set to 90%, 0.5 dB down from the 100% reference level is 

reported.

Grid

Enables and disables the display of a 10 x 10 grid on the FieldFox screen.

How to enable Grid display

— Press 

Mrk ->/Tools

— Then 

Grid

 

—

OFF

 Grid OFF

—

ON

 A grid of X/Y lines appears on the screen.

Trace Memory

A memory trace is a pulse measurement 

Tr 1

 data trace (NOT the trace in the 

Zoom window) that has been stored in the FieldFox volatile memory. It then 

becomes static, meaning it is not updated with normal pulse measurements. It 
can be displayed on the screen by itself, or with a pulse trace for comparison 
purposes.

The 

Tr 1

 data trace is displayed in 

yellow

.

The memory trace is displayed in 

blue

. 

How to display data and memory traces

— Press 

Trace 6

.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments