Keysight N9923A User Manual Download Page 252

Page: 252 / 276

252 Keysight N9923-90001 User’s Guide

Safety Considerations
Battery Protective Functions

Battery Protective Functions

The following protective functions are designed into the lithium-ion

rechargeable battery system used in FieldFox.

Do not pierce the battery with nails, strike the battery with a

hammer, step on the battery, or otherwise subject it to strong

impacts or shocks.
Do not solder directly onto the battery.

Do not expose the battery to water or salt water, or allow the

battery to get wet.

Do not disassemble or modify the battery. The battery contains

safety and protection devices, which if damaged, may cause the

battery to generate heat, explode, or ignite.
Do not place the battery in direct sunlight, or use or store the

battery inside cars in hot weather. Doing so may cause the battery

to generate heat, explode, or ignite. Using the battery in this

manner may also result in a loss of performance and a shortened

life expectancy.
There is a danger of explosion if the battery is incorrectly replaced.

Replace only with the same or equivalent type of battery

recommended. Discard used batteries according to manufacturer’s

instructions.
If you are charging the batteries internally, even while the FieldFox

is powered off, the FieldFox may become warm. Allow for proper

ventilation.
Do not discharge the battery using any device except the FieldFox

or the external battery charger (N9910X–872). When the battery is

used in a device other than those specified, it may damage the

battery or reduce its life expectancy. If the device causes an

abnormal current to flow, it may cause the battery to become hot,

explode, or ignite and cause serious injury.
For a Korean battery safety consideration translation, refer to

Appendix D:, “Korean Battery Safety Translation.”

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 252 / 276

Search results

Summary of Contents for N9923A

Reviews: