Keysight N9923A User Manual Download Page 181

Page: 181 / 276

Keysight N9923-90001 User’s Guide

181

Data Analysis Features
All about Markers

Figure 12-5 S11 of the same filter with same search criteria: -3 dB.

The same values would result from a search criteria of approxi30.4 dB.

Press

Enter

and four markers are automatically created to find the first

negative or positive bandpass over the displayed frequency range.

Bandwidth Search can be used ONLY with Log Mag display format.

The following six values are displayed for Bandwidth Search:

—

: Width of the filter. (marker 2 freq)

minus

(marker 3 freq).

—

Center

: Marker 4 frequency. Mathematical midpoint between marker 2 and

marker 3.

—

: Center Frequency / Bandwidth.

—

Loss

: Marker 1 amplitude.

—

Left

: Frequency of marker 2 or 3 (to left of marker 1).

—

Right

: Frequency of marker 2 or 3 (to right of marker 1).

Press

Back

to return to the previous menu.

Press

Peak Search

then choose from the following:

—

Peak

Moves the active marker to the HIGHEST amplitude data point of the

trace. Peak Excursion value is ignored. In SA Mode, the LO feed-through
signal (0 Hz) is also ignored.

—

Next Peak

Moves the active marker to the next highest amplitude peak from

where it currently resides.

—

Peak Left

Moves the active marker to the next data point to the left that

meets the ‘Peak’ criteria. When no data points to the left meet the ‘Peak’
criteria, the marker does not move.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 181 / 276

Search results

Summary of Contents for N9923A

Reviews: