manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 237 / 276

Share
Download
Keysight N9923A User Manual Download Page 237

 237

Keysight Handheld Analyzers
N99xxA User’s Guide

15 Using the Mini-USB Port to send SCPI Commands and 

Queries (Applies to N9912A units with serial number 

prefixes ≥5607 Only)

In this Chapter

Mini-USB Connection to PC with IO Libraries

The FieldFox comes with a mini-USB port that can be used to connect to your 
PC’s standard USB 2.0 port. Using Keysight IO Libraries, Connection Expert 
and connecting via a VISA connection, you can send SCPI commands via the 

Keysight Interactive IO

 window to the FieldFox. Refer to your IO Libraries 

online help for the details on connecting to your instrument. Refer to 

keysight.com

 to download the IO Libraries.

Overview of mini-USB to PC setup for sending SCPI commands and queries:

— Connect a mini-USB (FieldFox device-side) to standard USB (host-PC)

—

On the FieldFox

: Power on the instrument.

— Click 

System 7

 > 

System Diagnostics

 > 

System Information

 and find the 

FieldFox serial number.

—

On your PC

: Open the 

Keysight IO Libraries

 software, 

Connection Expert

 

and connect to the FieldFox using the VISA connection. Refer to the 
Keysight Connection Expert Help.

— In the 

Keysight Interactive IO

 window: Type in your SCPIs on the Command 

line and click 

Send Command

, 

Read Response

, or 

Send & Read

. Refer to 

the Keysight Connection Expert Help and 

Figure 15-1 on page 238

.

“Mini-USB Connection to PC with IO Libraries” on page 237

The FieldFox may be communicated with via the VISA libraries.  This 

makes it available to VEE, LabView, and other software tools that can 

communicate with VISA instruments.
You can connect to USB ports that are not type 2.0 USB. But, the 

mini-USB port is optimized for a type 2.0 USB ports. 

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments