Keysight N9923A User Manual Download Page 258

Page: 258 / 276

258 Keysight N9923-90001 User’s Guide

Safety Considerations
Packaging Markings

Packaging Markings

AC/DC Adapter Markings

This symbol on all primary and secondary packaging indicates compliance to

China standard GB 18455–2001.

The UL Marks are registered certification marks of Underwriters Laboratories Inc.

(UL). It means that UL has tested and evaluated representative samples of that

product and determined that it meets UL's safety requirements. When

accompanied by a 'C' and 'US', it indicates compliance to both Canadian and US

requirements.

NOM Mark (Normality of Mexico) indicates that the product was tested by an

accredited laboratory in Mexico and meets Mexico’s safety requirements.

Japan’s safety and EMC compliance mark.

China’s safety and EMC compliance mark.

Taiwan’s safety and EMC compliance mark.

Singapore’s safety mark.

Korea’s safety and EMC mark.

GOST, Russia’s safety and EMC mark.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 258 / 276

Search results

Summary of Contents for N9923A

Reviews: