Keysight N9923A User Manual Download Page 31

Page: 31 / 276

Keysight N9923-90001 User’s Guide 31

Preparing for Initial Use of Your New FieldFox
Take the FieldFox Tour

DC power connector used to connect to the AC/DC adapter. Maximum: 19

VDC, 4 ADC.

“Battery Usage” on

page 22

Micro Secure Digital slot. Use to extend the memory of the FieldFox.

“Set File Type and

Select Device” on

page 196

On the N9912A units with serial number prefixes

≥

5607 models, the

mini-USB port can be connected to your PC’s standard USB port to send

SCPI commands.

Standard USB connector used to connect a power sensor for Power Meter

Mode. Also used to save files to a USB flash drive.
Use of Keyboard and Mouse is NOT supported.

“How to Connect the

Power Sensor” on

page 127

Audio output jack.

Connector

Description

Learn More:

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 31 / 276

Search results

Summary of Contents for N9923A

Reviews: