manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 127 / 276

Share
Download
Keysight N9923A User Manual Download Page 127

Keysight N9923-90001 User’s Guide                                                                                                                      127

Power Meter (USB) Mode

Supported Power Sensors

For a complete list of supported Keysight USB Power Sensors, please visit: 

www.keysight.com/find/usbsensorsforfieldfox

How to Connect the Power Sensor

Connect your Power Sensor to one of the FieldFox USB ports.

A sequence of status lights are displayed on the base of the power sensor, 
when the FieldFox is in Power Meter (USB Sensor) mode. 

—

Green blinking

 light indicates the power sensor is communicating or 

self-tests are being performed. Because the FieldFox is usually 
communicating with the power sensor when it is connected, this is the 
normal mode of operation.

—

Amber light

 indicates Zeroing is being performed.

—

Red light

 indicates an error has occurred with the power sensor. Refer to 

power sensor documentation.

—

No light

 indicates the FieldFox is not communicating with the power 

sensor. This is the case when in Hold mode or when NOT in Power Meter 
Mode.

The FieldFox does NOT support the following Keysight USB Power Sensor 

features: External Triggering (Time Gated Burst Power Measurement), 

Power Sweep Operation, and Frequency Sweep Operation. External 

Zeroing is NOT allowed on the U2020 X-series Power Sensors.

Please refer to your USB Power Sensor User’s Guide and observe the 

damage levels of your device. 

Use an attenuator between the DUT and the power sensor when 

measuring power levels that are higher than +20 dBm. The attenuator 

value can be subtracted from the measurement using the Offset feature, 

discussed in 

“Relative and Offset Power Measurements” on page 131

.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments