Keysight N9923A User Manual Download Page 214

Page: 214 / 276

214 Keysight N9923-90001 User’s Guide

System Settings
Preferences

—Use the

arrows to highlight a setting.

—Then press

Edit

. The current setting changes to

yellow

—Some settings require you to press a softkey to change the value.

Otherwise, use the numeric keypad,

arrows, or rotary knob

to change the value.

—When finished changing a value, press

Done Edit

— When finished changing ALL preferences, press

Done

. All changes are

immediately saved as Preferences.

— To exit the editing session without saving changes, press

Esc

at any time.

Learn more about these preference settings:

Save and Reset Preferences

All preference settings can be made at one time from the Quick Settings table.

All settings that can be saved as preferences (except Battery Saver and Startup

Mode) can also be made from individual softkey selections throughout the
FieldFox menu structure. However, they remain through a FieldFox shut down
ONLY when the current settings are saved as preferences.

The table above shows a list of all of these settings and where they are
discussed in this User’s Guide.

Setting (Learn more...)

“Global Settings (Overview)” on page 215

—

“Language” on page 215

—

“Battery Saver” on page 216

—

“Startup Mode” on page 217

“Display Settings” on page 211

“Audio” on page 218

“Date and Time” on page 218

“GPS” on page 223

“File folders” on page 220

—

“Alpha Numeric Editing” on page 220

—

“File Saving Naming Options” on page 220

“CAT (Distance Units)” on page 220

“CAT/NA” on page 221

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 214 / 276

Search results

Summary of Contents for N9923A

Reviews: