Keysight N9923A User Manual Download Page 215

Page: 215 / 276

Keysight N9923-90001 User’s Guide

215

System Settings
Preferences

How to save current settings as Preferences

— Using softkeys, configure the settings as you would like them to remain.

— Press

System 7

— Then

Preferences

— Then

Save Current Settings

There is a beep when your settings have been

saved.

— Press

Reset Preferences

to restore the factory default settings.

Global Settings (Overview)

Choose the Global Settings values (Language, Batter Saver, and Startup
Mode). See also

“Quick Settings Table” on page 213

How to select Global Settings:

— Press

System 7

— Then

Preferences

— Then

Preferences

— Then use arrow softkeys or the knob to select Global Settings

— Then

Edit

for each of the following:

—Language (see)

—Batter Save Mode (see)

——On

——Off (default)

—Startup Mode (see)

— Then

Done Edit

(for each change in setting)

Language

Choose the language in which to display FieldFox softkeys and other
messages. Select Save Current Settings to set this language as a preference.

How to select a Language

— Press

System 7

— Then

Preferences

— Then

Language

— Then choose from the following:

—

English

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 215 / 276

Search results

Summary of Contents for N9923A

Reviews: