manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 213 / 276

Share
Download
Keysight N9923A User Manual Download Page 213

Keysight N9923-90001 User’s Guide

                                                                                                                      213

System Settings
Preferences

— Then 

Title ON OFF

 to make the title appear and disappear from the screen.

Edit Keywords

During a file save operation, keywords can be quickly appended to other text to 

create unique filenames. The Edit Keywords feature allows you to create 
custom keywords. Learn all about Edit Keywords in 

“Edit Keywords” on 

page 201

.

Full Screen Mode

Full Screen Mode maximizes the display of trace. The screen annotations and 
the soft keys are removed. 

— Press 

System 7

— Then 

Full Screen

To 

Exit

 full screen Mode, press any key.

Preferences

FieldFox preferences are settings that survive a shut down. When your FieldFox 

is turned OFF, then back ON, these settings remain. All preference settings can 
be restored to their factory defaults. Learn how in 

“Save and Reset 

Preferences” on page 214

. 

There are two ways to make FieldFox preference settings:

— From softkey selections throughout the FieldFox menu structure. Do this to 

temporarily try a setting, then press 

Save Current Preferences

. Learn how 

in the next section.

— From the Quick Settings table.

Quick Settings Table

All preferences can be set from the Quick Settings table. They are immediately 
saved as Preferences when 

Done

 is pressed.

How to view and change Preference Quick Settings

— Press 

System 7

— Then 

Preferences

 

— Then 

Preferences

— Press 

Next Page

 and 

Previous Page

 to view all settings. 

— To change a setting:

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments