Keysight N9923A User Manual Download Page 201

Page: 201 / 276

Keysight N9923-90001 User’s Guide

201

File Management
Saving and Recalling Files

—

Create Folder

A new folder is created in the current folder. Select a

name for the new folder from one of the displayed keywords: You can

change these keywords using the following

Edit Keywords

function.

Refer to Edit Keywords in

“Edit Keywords” on page 201

—

Delete Folder

The

selected

folder and its contents are deleted after a

warning prompt is displayed. A “Parent” folder or system folder can
NOT be deleted.

—

Copy Folder

The

selected

folder and its contents are copied and a

message is displayed telling you that the copy was successful.

——Then select a device to copy the folder to. Choose from

Copy

to Internal

Copy to USB

(must be inserted), or

Copy to SD

Card

(must be inserted).

——

Do Copy

to complete the file copy to the media/folder

selected.

—

Rename

The rename folder menu opens and the selected folder’s title

is displayed and available for editing.

—Press

Exit

when finished.

Edit Keywords

The preselected keywords (FILE, SITE, and so forth) can be edited to meet your
specific needs. Your keywords will remain in the FieldFox until you change

them. Keywords are limited to 30 characters.

How to edit keywords

— Press

Save/Recall 9

— Then

More

— Then

Edit Keywords

— Then

Next Page

and

Previous Page

to view all keywords.

— Use the

arrows to select a keyword to edit.

— When a keyword is selected, then press

Edit

— Then choose from the following:

—Press

Select

to add the cursor character to the end of the selected

keyword.

For more on renaming folders/files, refer to

“How to use the FieldFox

labeler ” on page 193

, and

“Prefixes and Suffixes for Filenames” on

page 202

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 201 / 276

Search results

Summary of Contents for N9923A

Reviews: