manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 223 / 276

Share
Download
Keysight N9923A User Manual Download Page 223

Keysight N9923-90001 User’s Guide

                                                                                                                      223

System Settings
System Configuration

For more information about Licensing, see the FieldFox Service Manual at: 

http://na.support.keysight.com/fieldfox.

GPS

GPS (Global Positioning System) allows you to ‘stamp’ each data trace with 
your physical position in latitude/longitude/elevation format. This can be 
useful when making measurements on cell towers or other antennas at remote 

locations.

— GPS can be used in all FieldFox modes.

— Your GPS settings can be saved with Preferences. Learn more on page 

“Preferences” on page 213

.

How to make GPS settings

— Press 

System 7

— Then 

System Configuration

— Then 

GPS

— Then choose from the following:

—

Display ON OFF

 Enable and disable the GPS display on the FieldFox main 

window. 

—

GPS

 

—

OFF

 - Disable GPS (default setting).

—

External

 - Enable GPS using an external, customer-supplied, USB 

dongle device. A check is made to detect a USB GPS device at the 
USB connectors.

When External is selected, a search is made for satellites overhead. GPS works 

best when outdoors and in full view of the open sky.  When several satellites 
are found, the following screen appears (when Display is set to ON) and is 
updated frequently:

This feature is usable ONLY with the GPS receiver that is shipped with 

Microsoft “Streets and Trips” and “AutoRoute”. The GPS receiver is NOT 

available from Keysight. Only the GPS USB receiver is used with the 

FieldFox. Therefore, it is NOT necessary to purchase the very latest version 

of the map software.

As the bar graph count exceeds 9 bars, the “dB” text is dropped from the 

number displayed on the bar. Units for C/No are dBHz.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments