Keysight N9923A User Manual Download Page 228

Page: 228 / 276

228 Keysight N9923-90001 User’s Guide

System Settings
System Configuration

— Press

.System 7

— Then

System Configuration

— Then

More

— Then

Update Time using Internet

— Connect a LAN cable that is also connected to the Internet.

— Then press

Update Time using Internet

. When successful, a message is

displayed indicating the amount of time correction that occurred.

— Optional: Set the following when a Proxy server is used to connect to the

internet:

—

Proxy Host

– Enter the name of the proxy host.

—

Proxy Port

– Enter the port number of the proxy host.

How to MANUALLY set Date and Time, Format, and Time Zone

— Press

System 7

— Then

System Configuration

— Then

More

— Then

Date and Time

— Press the

arrows to highlight the row to be edited.

— Then press

Edit

— Use the

arrows or rotary knob to select the field to be edited.

— Use the

arrows or numeric keypad to edit that field.

— Press

Cancel

Done

when the edits are complete.

Because of licensing security, the manual and GPS Sync methods to set

Date and Time are restricted as follows:
Can be set backward no more than 5 hours at a time.
Can be set forward any amount of time.
Can be set backward or forward no more than once in a day. A new day

begins at midnight.
There is no restriction for setting the Time Zone.

To change the Date and Time backward a significant amount, send an email to

[email protected]

BEFORE manually setting the Date and Time, be absolutely certain that the
Time Zone setting is correct.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 228 / 276

Search results

Summary of Contents for N9923A

Reviews: