Keysight N9923A User Manual Download Page 84

Page: 84 / 276

84 Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

—Press

Enter

Figure 5-1

Nominal Output Power

Coupled Frequency

This setting, especially useful for a Return Loss & DTF measurement, allows

both measurements to have different frequency ranges.

How to set Coupled Frequency

With a Return Loss & DTF measurement present:

— Press

Meas Setup 4

— Select the DTF measurement (Tr2) using the

arrows.

— Then choose from the following:

—

Coupled Freq ON

- Both the Return Loss and DTF traces have the same

frequency range settings.

—

Coupled Freq OFF

(default setting) - Both traces are allowed to have

individual frequency range settings. When set to OFF:

—The Return Loss measurement frequency settings are made in the

usual manner. Learn how at

“Frequency Range” on page 79

. When a

new Start or Stop frequency is selected, Coupled Frequency is
automatically set to OFF.

—The DTF measurement is made using the frequencies as determined by

the

DTF Frequency Mode

setting. Learn more in

“DTF Measurement

Settings” on page 91

Nominal here means: a general, descriptive term or design parameter. It is

not tested and not covered by the product warranty.
In FieldFox’s with FW <A.08.15, the Nominal Output displayed on the

bottom right side of the display indicates a range of low and high power

values. Your actual measured output power could be a little lower or a

little higher. Refer to

Figure 5-1

If you have the USB power sensor feature (Option 302) you can measure

the actual output power for your measurement. Refer to page

Chapter 8,

“Power Meter (USB) Mode.”

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 84 / 276

Search results

Summary of Contents for N9923A

Reviews: