Keysight N9923A User Manual Download Page 199

Page: 199 / 276

Keysight N9923-90001 User’s Guide

199

File Management
Saving and Recalling Files

Manage Files

Files that are stored in the FieldFox internal memory, standard SD card, and
USB Flash drive, can be copied to another device or deleted.

How to Manage files

— Press

Save/Recall 9

— Then

Device

to select the location (Internal, USB, or standard SD Card) of

the file to copy or delete.

— Then

More

— Then

Manage Files

— Then choose from the following:

—

Select Files

Selects a file or files to sort, copy, or delete.

—

Sort

—

Sort by Name

Sorts the displayed list of files by name.

—

Sort by Date

Sorts the displayed list of files by date.

—

Copy

Select a file or files to copy.

— Then select a device to copy the file to. Choose from

Copy to Internal

Copy

to USB

(must be inserted), or

Copy to SD Card

(must be inserted).

—

Do Copy

to complete the file copy to the media/folder selected.

—

Delete

—

Yes

The selected file is deleted.

—

Cancel

To cancel Delete and return to previous menu.

—

More

—

Select Files

Selects a file or files to sort, copy, or delete.

—

Select All

selects all of the displayed files. All files that are displayed

are to be copied. Then select a device and a folder to copy the file to.

Choose from Internal, USB (must be inserted), or SD Card (must be
inserted).

—

Clear All

Deselects all of the displayed files.

When selecting

Internal

, it may also be necessary to first select

Manage

Folders

to specify an active folder which contains the files to copy or

delete. Refer to

“Manage Folders” on page 200

Copy

can be done to any FieldFox internal folder, standard SD folder, or

USB storage device.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 199 / 276

Search results

Summary of Contents for N9923A

Reviews: