manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 217 / 276

Share
Download
Keysight N9923A User Manual Download Page 217

Keysight N9923-90001 User’s Guide

                                                                                                                      217

System Settings
Preferences

Startup Mode

The Startup Mode setting determines the mode that becomes active (visible) 
when User Preset is set to OFF (Factory Preset) and the FieldFox is powered 
ON. See 

“User Preset” on page 209

.

How to setup Startup Mode

— Press 

System 7

— Then 

Preferences

 

— Then 

Preferences

— Then scroll to 

Global Settings

 > 

Startup Mode

 and press 

Edit

.

— Then repeatedly press the 

Startup Mode

 to scroll through the available 

choices.

—

<Default>

 is the factory default mode for your FieldFox model.

—Built-in Power Meter Mode is NOT allowed as a Startup Mode.

Display

Choose the Display values (Display Colors, Trace Width, Brightness, Title 
Enabled, Title). See 

“Display Settings” on page 211

.

How to select Display values:

— Press 

System 7

— Then 

Preferences

— Then 

Preferences

— Then use arrow softkeys or the knob to select 

Display

 

— Then 

Edit

 for each of the following:

— Display Colors

— Indoor (default)

— Night Vision

— Outdoor Sun

— Outdoor Dusk

— Outdoor Clouds

— Trace Width

— Normal (default)

— Wide

— Brightness

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments