Keysight N9923A User Manual Download Page 239

Page: 239 / 276

239

Keysight N9923A Handheld Analyzer
User’s Guide

16 Working with the Lithium-Ion Battery

In this Chapter

See Also:

Viewing the Battery Charge Status

You can view the battery charge status in the following ways:

— Icons in the upper right of the front panel screen.

— Battery screen - select

System

then

Service Diagnostics

then

Battery

— Built-in battery gauge. Learn more in the following section.

“Viewing the Battery Charge Status” on page 239

“Charging the Battery” on page 241

“Reconditioning Battery” on page 244

“Battery Care” on page 244

“Maximizing Battery Life” on page 244

“Lithium-Ion Battery Disposal” on page 245

“Install the Lithium-Ion Battery” on page 22

“To conserve battery power:” on page 23

“For the Battery” on page 251

Table 16-1

Front Panel Icons

Icon

Status

Connected to external power through the

AC/DC adapter. Battery installed and charging.

The amount of charge is indicated by the

number of bars shown.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 239 / 276

Search results

Summary of Contents for N9923A

Reviews: