Keysight N9923A User Manual Download Page 78

Page: 78 / 276

78 Keysight N9923-90001 User’s Guide

CAT (Cable and Antenna Test) Mode
CAT Mode Settings

—

Cable Loss (1-Port)

1-port reflection measurement that displays the loss of

a transmission line. Learn more on

page 86

—

Insertion Loss (2-Port)

2-port transmission measurement that accurately

displays the loss through a cable or other device in dB. Both ends of the

cable must be connected to the FieldFox. NO phase information is included
in this measurement. Learn more at

“2-Port Insertion Loss Measurements”

on page 88

. This feature is available only with an option on some FieldFox

models. For detailed information, please view the FieldFox Configuration
Guide at:

http://literature.cdn.keysight.com/litweb/pdf/5990-9836EN.pdf

—

DTF (Lin)

Distance to Fault in Linear format.

—

TDR (Lin rho)

The Y-axis of the display is linear, real, unitless values. A trace

without reflections shows as 0 (zero). Maximum reflections from an open or
short show as 1.

—

TDR (ohm)

The Y-axis of the display is impedance (ohms).

—

TDR & DTF

TDR and DTF are displayed.

Quick Settings Table

Both CAT and NA Modes allow you to view and change most relevant settings
from a single location. All of these settings are discussed in this chapter and,
unless otherwise noted, ALL of these settings can also be made using the

standard softkey menus.

How to view and change Quick Settings

— Press

Meas Setup 4

— Then

Settings

— Press

Next Page

and

Previous Page

to view all settings. If these softkeys

are NOT available, then all available settings fit on one page.

— To change a setting:

—Use the

arrows to highlight a setting.

—Then press

Edit

. The current setting changes to

yellow

—Some settings require you to press a softkey to change the value.

Otherwise, use the numeric keypad,

arrows, or rotary knob to

change the value.

—When finished changing a value, press

Done Edit

— Press

Dock Window

to relocate the Settings table to a position relative to

the trace window. The Dock Window setting persists through a Preset.
Choose from the following

—

Full

(Default setting) Only the Settings table is shown on the screen.

The trace window is temporarily not shown

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 78 / 276

Search results

Summary of Contents for N9923A

Reviews: