Keysight N9923A User Manual Download Page 175

Page: 175 / 276

Keysight N9923-90001 User’s Guide

175

Data Analysis Features
All about Markers

Figure 12-1 Marker 2 is Active, marker 1 is NOT active.

About Delta Markers

A delta marker provides X-and Y-axis readout information that is

relative

to a

‘reference’ marker.

A delta marker is created with a

(delta symbol) to distinguish it from the

reference marker.

All six markers can be delta/reference marker pairs.

Peak search functions can be performed using delta markers. The delta marker
moves to the peak; the reference marker does NOT move.

Figure 12-2 A Delta marker and its associated reference marker.

In the graphic above, the marker readout shows the difference between the
two markers in frequency and amplitude.

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 175 / 276

Search results

Summary of Contents for N9923A

Reviews: