Keysight N9923A User Manual Download Page 174

Page: 174 / 276

174 Keysight N9923-90001 User’s Guide

Data Analysis Features
All about Markers

All about Markers

Markers move along the X-axis range of the measurement trace to provide a

numerical readout of each measured data point. Markers also allow you to
search for specific Y-axis values.

A trace can contain up to six markers.

The marker readout on the FieldFox screen displays X and Y-axis information

for the current active marker ONLY.

A Marker Table can be displayed that allows you to simultaneously view X and

Y-axis information for all markers.

Markers can be used in

CAT

, and

Pulse Measurements

Modes.

How to create Markers

— Press

Marker

— Then

Markers 1...6

to select a marker to activate.

— Then

Normal

to activate that marker. A marker is created on the trace in the

middle of the X-axis. That marker is now

active

— Then move the marker using the rotary knob, the

arrows, or by

entering an X-axis position with the number keys.

— Then press

Enter

How to move a Marker after it is created

— Press

Marker

— Then

Markers 1...6

repeatedly until the marker of interest is selected. The

OFF, Normal, or Delta softkey is black to indicate the current setting of
each marker.

— Then move the marker as when it was first created.

— Markers can also be moved using one of the marker search functions. Learn

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 174 / 276

Search results

Summary of Contents for N9923A

Reviews: