Home
/
Keysight
/
N9923A
/
User Manual

Keysight N9923A, User Manual, Page: 185 / 276

Share

Page: 185 / 276

Keysight N9923A User Manual Download Page 185

Keysight N9923-90001 User’s Guide

185

Data Analysis Features
All about Limit Lines

All about Limit Lines

Limit lines are visual representations, drawn on the FieldFox screen, of the

specified limits for a measurement. With this capability, you can easily
compare measured data versus specifications. Optionally, you can enable an
audible beep and display

Pass or Fail

information for each measurement.

— You can have up to as many limit line segments as there are data points for

each measurement trace allowing you to test all aspects of your
measurements.

— Limit lines are available in CAT Mode, NA Mode, and SA Mode. Power Meter

Mode uses different limit settings. Learn more in

“Limits” on page 133

— Limit lines and limit testing are NOT allowed in NA Mode with

Smith Chart

or

Polar

display formats.

— Limit lines can be saved and recalled with an *.sta file. Learn more in

Files” on page 195

. They can also be saved and recalled independently

from the Limit softkeys. Learn more in

“How to Save and Recall Limits” on

How to Create Fixed Limit Lines

There are two ways to build a Fixed limit line:

1.

Build (limits) From a Trace. Learn how in

“Build From Trace” on page 187

.

2.

Enter X/Y data points into the on-screen editor. The limit line is formed as

the FieldFox ‘connects the dots’ on the screen. To create frequency gaps

that are NOT tested, use separate limit lines. The X-axis values for two

lines can overlap.

— Press

Limit 8

.

— Then

Edit Limits

. A limit line table appears.

— Use the Up / Down arrows and rotary knob to navigate the cursor to the

following editable cells.

—

Description

- Press

Edit

, then enter a description for the limit line using the

FieldFox labeler. Learn how in

“How to use the FieldFox labeler ” on

—

Fixed/Relative

– Press

Edit

to toggle between the following:

——

Fixed

- the limit line does not move. The X/Y coordinates are

absolute locations on the screen.

——

Relative

- the limit line moves relative to the center frequency

and reference level.

Note

: It is easiest to first create Fixed

Limits, then change this setting to Relative. Learn more

“Relative Limit Lines” on page 186

—

Upper/Lower

– Press

Edit

to toggle between the following:

«
...
183
184
185
186
187
...
»

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments