manualshive.com logo in svg

Keysight N9923A, User Manual, Page: 229 / 276

Share
Download
Keysight N9923A User Manual Download Page 229

Keysight N9923-90001 User’s Guide

                                                                                                                      229

System Settings
System Configuration

— Press 

Done

 to exit the Date and Time settings. The readout in the 

upper-right corner of the FieldFox screen will update accordingly.

LAN Settings

Configure the LAN settings to be used to communicate with the Data Link 
Software and connect to the FieldFox for remote SCPI operation. Learn more 
about Data Link at: 

www.keysight.com/find/fieldfoxsupport

.

How to configure LAN settings

The first three ‘Current...’ settings can NOT be edited.

— Press 

System 7

.

— Then 

System Configuration

.

— Then 

More

.

— Then 

LAN

.

— Use the 

 arrows to select one of the following, then press 

Edit

.

—

Hostname

 Change the name that can be used to address the FieldFox if 

your server supports this feature. The default hostname is generated 
automatically. 

—

Obtain IP

 Choose from:

—

DHCP

 - IP Address is assigned dynamically. If your server supports this 

feature, the IP Address for the FieldFox is assigned each time it is 

started. 

—

Static

 - Set the IP Address manually. The Address remains until you 

change it.

Summary of Contents for N9923A





















































































































































































































































































Reviews:

No comments