Keysight N9923A User Manual Download Page 234

Page: 234 / 276

234 Keysight N9923-90001 User’s Guide

System Settings
FieldFox Package Installer (Applies to N9912A units with serial number prefixes ≥5607)

— Then

Backup Data

— A message is displayed: “

Choose backup file location.

”

— Then choose either

SD Card

USB

— A progress bar and a message is displayed: “

Saving user data…

”

— Press

Cancel

to exit without backing up your files and returning to the initial

Installer menu.

How to restore files

This procedure restores user files from a USB or SD card. See also

“How to backup

files” on page 233

If your stored any user files to a USB or SD card, this procedure restores those
files.

From the initial Installer menu:

— Press

Utility

— Then

Cancel

to exit without restoring your files and returning to the initial

Installer menu.

Press

Restore Data

— A message is displayed: “T

his option will COMPLETELY ERASE

existing user data. ARE YOU SURE?

”

— Then

to return to the previous menu without restoring files.

Press

Yes

— Then choose either

SD Card

USB

A progress bar and a message is displayed: “

Restoring user data…

”

Restoring files overwrites the existing user data on the FieldFox.

If you backup multiple versions of the user files, the FieldFox appends a

“_#” to each subsequently stored file. During restore, the file with the
highest appended number is loaded into the FieldFox

Summary of Contents for N9923A





















































































































































































































































































Search results

Summary of Contents for N9923A

Reviews:

Keysight N9923A, User Manual, Page: 234 / 276

Search results

Summary of Contents for N9923A

Reviews: