Hitachi H8/326 Series Hardware Manual Download Page 60

Page: 60 / 328

Figure 3-10. Block Data Transfer Instruction/EEPROM Write Operation Code

Notes on EEPMOV Instruction

1. The EEPMOV instruction is a block data transfer instruction. It moves the number of bytes

specified by R4L from the address specified by R5 to the address specified by R6.

2. When setting R4L and R6, make sure that the final destination address (R6 + R4L) does not

exceed H'FFFF. The value in R6 must not change from H'FFFF to H'0000 during execution of

the instruction.

3.6 CPU States

The CPU has three states: the program execution state, exception-handling state, and power-down

state. The power-down state is further divided into three modes: the sleep mode, software standby

mode, and hardware standby mode. Figure 3-11 summarizes these states, and figure 3-12 shows a

map of the state transitions.

Figure 3-11. Operating States

EEPROM

State

Program execution state

The CPU executes successive program instructions.

Exception-handling state

A transient state triggered by a reset or interrupt. The CPU executes a hardware

sequence that includes loading the program counter from the vector table.

Power-down state

Sleep mode

A state in which some or all of the chip

Software standby mode

functions are stopped to conserve power.

Hardware standby mode

→

R5 + R4L

→

←

R6 + R4L

H'FFFF

Not allowed

→

R5 + R4L

→

←

R6 + R4L

Op: Operation field

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands