Hitachi H8/326 Series Hardware Manual Download Page 324

Page: 324 / 328

ADCSR—A/D Control/Status Register

H'FFE8

A/D

Bit

ADF

ADIE

ADST

SCAN

CKS

CH2

CH1

CH0

Initial value

Read/Write

R/(W)*

R/W

Channel Select
CH2

CH1 CH0

Single mode Scan mode

, AN

to AN

, AN

to AN

Clock Select
0 Conversion time = 242 states (max)
1 Conversion time = 122 states (max)

Scan Mode
0 Single mode
1 Scan mode

A/D Start

0 A/D conversion is halted.
1 1. Single mode: One A/D conversion is performed, then this bit is automatically cleared to “0.”

2. Scan mode: A/D conversion starts and continues cyclically on all selected channels until “0”

is written in this bit.

A/D Interrupt Enable
0 The A/D interrupt request (ADI) is disabled.
1 The A/D interrupt request (ADI) is enabled.

A/D End Flag
0 Cleared from “1” to “0” when CPU reads ADF = “1,” then writes “0” in ADF.
1 Set to “1” at the following times:

1. Single mode: at the completion of A/D conversion
2. Scan mode: when all selected channels have been converted.

Note: * Software can write a “0” in bit 7 to clear the flag, but cannot write a “1” in this bit.

315

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands