manualshive.com logo in svg

Hitachi H8/326 Series, Hardware Manual

The Hitachi H8/326 Series Hardware Manual is an essential resource for users of this powerful product. Easily accessible for free download at manualshive.com, this comprehensive manual provides detailed instructions, diagrams, and troubleshooting tips to ensure optimal usage and understanding of the H8/326 Series functionalities.

Share
Download
background image

•  Receiving Serial Data: Follow the procedure below for receiving serial data.  When switching

from asynchronous mode to clocked synchronous mode, be sure to check that PER and FER are

cleared to “0.”  If PER or FER is set to “1” the RDRF bit will not be set and both transmitting and

receiving will be disabled.

Figure 8-15.  Sample Flowchart for Serial Receiving

Start receiving

Read RDRF bit in SSR

RDRF = “1”?

Read receive data 

from RDR, and clear 

RDRF bit to “0” in SSR

ORER = “1”?

Read ORER in SSR

Finished

receiving?

Clear RE to “0” in SCR

End

Error handling

1

2

3

No

Yes

Yes

No

No

Yes

4

1.

SCI initialization: the receive data function of the RxD pin is 
selected automatically.

3.

To continue receiving serial data: read RDR and clear RDRF to 
“0” before the MSB (bit 7) of the current frame is received.

4.

Receive error handling: if a receive error occurs, read the ORER 
bit in SSR then, after executing the necessary error handling, 
clear ORER to “0.”  Neither transmitting nor receiving can 
resume while ORER remains set to “1.”  When clock output
mode is selected, receiving can be halted temporarily by 
receiving one dummy byte and causing an overrun error.  
When preparations to receive the next data are completed, clear 
the ORER bit to “0.”  This causes receiving to resume, so 

Clear ORER to “0” in SSR

Return

Overrun error handling

2.

SCI status check and receive data read: read the serial status 
register (SSR), check that RDRF is set to “1,” then read receive 
data from the receive data register (RDR) and clear RDRF to “0.” 
Transition of the RDRF bit from “0” to “1” can be reported by an 
RXI interrupt.

return to the step marked 2 in the flowchart.

Start error handling

Initialize

202

Summary of Contents for H8/326 Series









































































































































































































































































































































Reviews:

No comments

Related manuals for H8/326 Series

Dave Embedded Systems ARM Cortex-A9 MPCore Quick Start Manual preview
ARM Cortex-A9 MPCore
Brand: Dave Embedded Systems Pages: 67
Xinje XG Series User Manual preview
XG Series
Brand: Xinje Pages: 76
Commell ES-270 User Manual preview
ES-270
Brand: Commell Pages: 36
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
Endace DAG 7.1S User Manual preview
DAG 7.1S
Brand: Endace Pages: 51
ETC Power Control Processor Configuration Manual preview
Power Control Processor
Brand: ETC Pages: 64
Intel Core 2 Quad Q9400 Product Brief preview
Core 2 Quad Q9400
Brand: Intel Pages: 2
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
B&B Electronics 232PCC User Manual preview
232PCC
Brand: B&B Electronics Pages: 17
Idis DR-8364F Quick Manual preview
DR-8364F
Brand: Idis Pages: 16
ADTRAN Total Access 1500 Dual FXS/DPO Quick Start Manual preview
Total Access 1500 Dual FXS/DPO
Brand: ADTRAN Pages: 2
Ciara Horizon D10750 Disassembly Manual preview
Horizon D10750
Brand: Ciara Pages: 14
nox Hummer H-240CL Manual preview
Hummer H-240CL
Brand: nox Pages: 16
Beckhoff CU8210-D001-0200 Manual preview
CU8210-D001-0200
Brand: Beckhoff Pages: 25
ICP DAS USA ET-7017-10 Quick Start Manual preview
ET-7017-10
Brand: ICP DAS USA Pages: 8
LevelOne CamCon FCS-4000 User Manual preview
CamCon FCS-4000
Brand: LevelOne Pages: 94
Dahua Technology VDA-NVR2108W4KS2 User Manual preview
VDA-NVR2108W4KS2
Brand: Dahua Technology Pages: 363

Brands by name

Popular brands

Load more brands