Hitachi H8/326 Series Hardware Manual Download Page 248

Page: 248 / 328

Section 12. Power-Down State

12.1 Overview

The H8/329 Series has a power-down state that greatly reduces power consumption by stopping

some or all of the chip functions. The power-down state includes three modes:

(1) Sleep mode – a software-triggered mode in which the CPU halts but the rest of the chip

remains active

(2) Software standby mode – a software-triggered mode in which the entire chip is inactive

(3) Hardware standby mode – a hardware-triggered mode in which the entire chip is inactive

Table 12-1 lists the conditions for entering and leaving the power-down modes. It also indicates the

status of the CPU, on-chip supporting modules, etc. in each power-down mode.

Table 12-1. Power-Down State

Entering

CPU

Sup.

I/O

Exiting

Mode

procedure

Clock

CPU

Reg’s.

Mod.

RAM

ports

methods

Sleep Execute

Run

Halt

Held

Run

Held

• Interrupt

mode

SLEEP

• RES

instruction

• STBY

Soft-

Set SSBY bit

Halt

Held

Halt

Held

• NMI

ware

in SYSCR to

and

• IRQ

– IRQ

standby

“1,” then

initial-

• STBY

mode

execute SLEEP

ized

• RES

instruction

Hard-

Set STBY

Halt

Not

Halt

Held

High

• STBY High,

ware

pin to Low

held

and

impe-

then RES

standby

level

initialized

dance

Low

→

High

mode

state

Notes: 1. SYSCR: System control register

2. SSBY:

Software standby bit

239

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands