Hitachi H8/326 Series Hardware Manual Download Page 75

Page: 75 / 328

If execution of interrupt-handling routines under these conditions is not desired, it can be

avoided by using the following procedure to disable and clear interrupt requests.

Set the I bit to “1” in the CCR, masking interrupts. Note that the I bit is set to 1 automatically

when execution jumps to an interrupt vector.

Clear the desired bits from IRQ

E to IRQ

E to “0” to disable new interrupt requests.

Clear the corresponding IRQ

SC to IRQ

SC bits to “0,” then set them to “1” again. Pending

IRQ

interrupt requests are cleared when I = “1” in the CCR, IRQ

SC = “0,” and IRQ

E = “0.”

4.3.3 External Interrupts

The external interrupts are NMI and IRQ

to IRQ

. These four interrupts can be used to recover

from software standby mode.

(1) NMI: A nonmaskable interrupt is generated on the rising or falling edge of the NMI input

signal regardless of whether the I (interrupt mask) bit is set in the CCR. The valid edge is selected

by the NMIEG bit in the system control register. The NMI vector number is 3. In the NMI

hardware exception-handling sequence the I bit in the CCR is set to “1.”

(2) IRQ

to IRQ

: These interrupt signals are level-sensed or sensed on the falling edge of the

input, as selected by ISCR bits IRQ

SC to IRQ

SC. These interrupts can be masked collectively by

the I bit in the CCR, and can be enabled and disabled individually by setting and clearing bits

IRQ

E to IRQ

E in the IRQ enable register.

When one of these interrupts is accepted, the I bit is set to “1.” IRQ

to IRQ

have interrupt vector

numbers 4 to 6. They are prioritized in order from IRQ

(Low) to IRQ

(High). For details, see

table 4-2.

Interrupts IRQ

to IRQ

do not depend on whether pins IRQ

to IRQ

are input or output pins.

When using external interrupts IRQ

to IRQ

, clear the corresponding DDR bits to “0” to set these

pins to the input state, and do not use these pins for input to the A/D converter.

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands