Hitachi H8/326 Series Hardware Manual Download Page 222

Page: 222 / 328

The ADCSR is initialized to H'00 at a reset and in the standby modes.

Bit 7—A/D End Flag (ADF): This status flag indicates the end of one cycle of A/D conversion.

Bit 7

ADF

Description

To clear ADF, the CPU must read ADF after

(Initial value)

it has been set to “1,” then write a “0” in this bit.

This bit is set to 1 at the following times:

(1) Single mode: when one A/D conversion is completed.

(2) Scan mode: when inputs on all selected channels have been

converted.

Bit 6—A/D Interrupt Enable (ADIE): This bit selects whether to request an A/D interrupt (ADI)

when A/D conversion is completed.

Bit 6

ADIE

Description

The A/D interrupt request (ADI) is disabled.

(Initial value)

The A/D interrupt request (ADI) is enabled.

Bit 5—A/D Start (ADST): The A/D converter operates while this bit is set to “1.” This bit can be

set to “1” by the external trigger signal ADTRG.

Bit 5

ADST

Description

A/D conversion is halted.

(Initial value)

(1) Single mode: One A/D conversion is performed. The ADST bit is

automatically cleared to “0” at the end of the conversion.

(2) Scan mode: A/D conversion starts and continues cyclically on the

selected channels until the ADST bit is cleared to “0” by software (or

a reset, or by entry to a standby mode).

213

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands