Hitachi H8/326 Series Hardware Manual Download Page 212

Page: 212 / 328

In receiving, the SCI operates as follows.

1. If an external clock is selected, data are input in synchronization with the input clock. If clock

output is selected, as soon as the RE bit is set to “1” the SCI begins outputting the serial clock

and inputting data. If clock output is stopped because the ORER bit is set to “1,” output of the

serial clock and input of data resume as soon as the ORER bit is cleared to “0.”

2. Receive data are shifted into RSR in order from LSB to MSB.

After receiving the data, the SCI checks that RDRF is “0” so that receive data can be loaded

from RSR into RDR. If this check passes, the SCI sets RDRF to “1” and stores the received

data in RDR. If the check does not pass (receive error), the SCI operates as indicated in

table 8-8.

Note: Both transmitting and receiving are disabled while a receive error flag is set. The RDRF bit

is not set to “1.” Be sure to clear the error flag.

3. After setting RDRF to “1,” if the RIE bit (receive-end interrupt enable) is set to “1” in SCR, the

SCI requests an RXI (receive-end) interrupt. If the ORER bit is set to “1” and the RIE bit in

SCR is set to “1,” the SCI requests an ERI (receive-error) interrupt.

When clock output mode is selected, clock output stops when the RE bit is cleared to “0” or the

ORER bit is set to “1.” To prevent clock count errors, it is safest to receive one dummy byte

and generate an overrun error.

203

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands