Hitachi H8/326 Series Hardware Manual Download Page 178

Page: 178 / 328

Bit 3—Stop Bit Length (STOP): This bit selects the number of stop bits. It is ignored in the

synchronous mode.

Bit 3

STOP

Description

One stop bit

(Initial value)

Transmit: one stop bit is added.

Receive: one stop bit is checked to detect framing errors.

Two stop bits

Transmit: two stop bits are added.

Receive: the first stop bit is checked to detect framing errors; if the second bit is a space

(0), it is regarded as the next start bit.

Bit 2—Multiprocessor Mode (MP): This bit selects the multiprocessor format in asynchronous

communication. When multiprocessor format is selected, the parity settings of the parity enable bit

(PE) and parity mode bit (O/E) are ignored. The MP bit is ignored in synchronous communication.

The MP bit is valid only when the MPE bit in the serial/timer control register (STCR) is set to “1.”

When the MPE bit is cleared to “0,” the multiprocessor communication function is disabled

regardless of the setting of the MP bit.

Bit 2

Description

Multiprocessor communication function is disabled.

(Initial value)

Multiprocessor communication function is enabled.

Bits 1 and 0—Clock Select 1 and 0 (CKS1 and CKS0): These bits select the internal clock

source when the baud rate generator is clocked from within the chip.

Bit 1

Bit 0

CKS1

CKS0

Description

Ø clock

(Initial value)

Ø/4 clock

Ø/16 clock

Ø/64 clock

169

Summary of Contents for H8/326 Series









































































































































































































































































































































Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands

Hitachi H8/326 Series, Hardware Manual

Search results

Summary of Contents for H8/326 Series

Reviews:

Related manuals for H8/326 Series

Brands by name

Popular brands