Franklin Electric CERUS X-DRIVE CXD-003A-4V, Installation And Operation Manual

Page: 203 / 252

PARAMETER REFERENCE TABLES
Parameter Descriptions > SET Menu
203
SET-19 0019 N PID F/B Unit 0_PSI
1_inWC
2_Feet
3_F
4_CFM
5_GPM
6_%
7_Cust
8_inHg
9_m
10_mBar
11_Bar
12_kPa
13_C
14_LPM
15_CMH
Measurement unit selection for feedback signal.
SET-20 0020 N PID F/B Max 0.0 to 32767 PID feedback transducer maximum range
SET-21 0021 Y PID Set-point 0.0 to [SET-20] ( [SET-19] Unit) Set the desired value for PID (pressure, temperature, GPM, etc.).
SET-22 0022 Y PID Lo Hz Limit [SET-13] to [SET-23] (Hz) Low frequency limit in PID mode. PID Low Frequency is limited by
Low Frequency [SET-13] and PID High Frequency [SET-23] .
SET-23 0023 N PID Hi Hz Limit [SET-22] to [SET-14] (Hz) High frequency limit in PID mode. PID High Frequency is limited by High Fre -
quency [SET-14] and PID Low Frequency [SET-22] .
SET-24 0024 Y PID P-Gain 0 to 100% Proportional-Gain determines PID control sensitivity. Greater values pro -
vide more sensitivity. However, if set too high, the system may create an
output frequency oscillation and instability. Used along with
PID I-TIme [SET-25] to smooth and balance system response.
SET-25 0025 Y PID I Time 0.0 to 100 sec Integral-Time determines PID response time. Lower values increase system
response to the feedback signal, which reduces overshoot, but may cause
system oscillation if set too low. Greater values provide slower response,
which may cause overshoot of the setpoint and oscillation of output fre -
quency.
SET-26 0026 Y Sleep Mode 0_Disabled
1_Sleep Only
Boost
Sleep Mode selection for pressure controlled systems, such as pumping
applications. Boost increases the process control value (pressure)
before going to sleep.
SET-27 0027 Y Sleep Chk Time 5 to 120 sec Time delay (sleep check cycle time) before each Sleep Check process.
SET-28 0028 Y Sleep Delay 0 to 3000 sec Delay before VFD triggers Sleep Mode state when all other conditions are
met.
SET-29 0029 Y S-Boost Value 0 to 10% Sleep Boost Value: Value added to original setpoint to provide a pressure
boost before entering sleep.
SET-30 0030 Y S-Boost Timer 5 to 120 sec Sleep Boost Timer: Limits duration of sleep boost operation if Sleep Boost
set-point is not reached.
SET-31 0031 Y Wake-Up Level 0.0 to [SET-21] ( [SET-19] Unit) Sets a wakeup level for VFD to exit Sleep mode and start running.
SET-32 0032 Y S-Bump Timer 5 to 120 sec Sleep Bump Timer: Sets a duration time for pressure bump to increase sys -
tem pressure.
SET-33 0033 Y Pipe Fill Timer 0.0 to 60 min Pipe Fill mode exit timer to switch to PID mode. If set to 0.0 min, pipe fill is
disabled.
SET-34 0034 Y P-Fill Exit Lvl 0.0 to [SET-21] ( [SET-19] Unit) If feedback reaches [SET-34] value, VFD will switch from pipe fill mode to PID
control mode.
SET-35 0035 Y Pipe Fill Freq [SET-22] to [SET-23] (Hz) VFD will vary the output frequency from [ADV2-68] to [SET-35] trying to main -
tain 60% of [SET-34] value.
SET-36 0036 Y Broken Pipe Lvl 0.0 to [SET-21] (PSI) If VFD runs above [SET-37] frequency for [SET-38] delay with system pressure
below [SET-36] , it will trip on Broken Pipe fault. If [SET-36] is set to 0, this pro -
tection will be disabled.
SET-37 0037 Y Broken Pipe Frq [SET-22] to [SET-23] (Hz) If VFD is running above this speed with pressure below [SET-36] , Broken Pipe
Delay timer starts.
SET-38 0038 Y Broken Pipe Dly 0 to 6000 sec If Broken Pipe Delay timer runs longer than this setting, VFD trips on Broken
Pipe fault.
SET-39 0039 Y OverPress Set 0_Disabled
1_OP Trip
2_OP Auto Reset
Overpressure protection settings
OP Trip: When tripped on overpressure, VFD will require a reset.
OP Auto Reset: occurs when pressure drops below Wake-up Level [SET-31] .
CODE Mod
Bus AR Display Name
Range Description